DuPont ™ Flashing Tape. Enhance the long-term performance of your building openings with DuPont ™ Flashing Tape. This easy-to-use self-adhered tape helps protect heads and jambs of rectangular windows and doors from intrusion by outdoor air, bulk water and wind-driven rain. By helping to better seal the building envelope, DuPont. Flashing an exterior door, step by step. First, read the installation instructions provided by the door manufacturer. Unless these instructions violate basic flashing principles, you should follow these instructions. Next, verify that the rough opening is the right size. In most cases, the rough opening should be 1/2 inch higher than the door. In fact the absence of effective flashing at this 20-year-old sliding glass door (photo above) led to the need for a complete door, door jamb, and trim replacement on this Poughkeepsie home. When the new door was installed we included a sit-built pan flashing and membrane flashing around the door for a more durable replacement. Area prior to membrane installation for full adhe-sion of the membrane to the structural sill. Refer to 'Table I – Flashing Lengths and Cut Formulas,' (page 8), to determine appropriate flashing lengths. After the membrane has been installed, roll firmly into place. Install membrane such that all laps shed water (following the.
- POST a QUESTION or COMMENT about how to buy & apply peel and stick flashing tape around window & doors or at housewrap joints or holes.
InspectAPedia tolerates no conflicts of interest. We have no relationship with advertisers, products, or services discussed at this website.
Window & door details when using peel and stick flashing tape or membranes:
What is are best position & sequence for installing stick-on flashing tape over, under and along the sides of a window or door? This article gives recommended & best practices for using flashing tape around window openings. We explain why you should not stick the tape right onto housewrap over or under a window.
This article series describes the selection and installation of peel-and-stick flashing membranes used on building exteriors to seal housewrap joints and to seal against air or water leaks around windows, doors, or other openings. Our photo at page top shows Typar® flashing tape installed above a new window. A better practice laps the housewrap over rather than under the stick-on flashing tape, a better detail but one omitted by many builders.
We also provide an ARTICLE INDEX for this topic, or you can try the page top or bottom SEARCH BOX as a quick way to find information you need.
Details for Installing Peel and Stick Flashing Tape at Windows & Doors
How To Install Garage Door Flashing Tape
We like to install flashing tape in the same sequence or overlap pattern as if it were metal flashing - that is, the upper horizontal flashing tape overlaps the vertical tape installed (first) at the sides of the window.
To assure that we respect that water runs downhill, we install housewrap, window and then peel and stick flashing tape around a window in this order:
- The rough openings for windows and doors are cut before the housewrap is installed. This permits the housewrap to lap inside and be stapled to the frame of the rough opening. In our photo (left) you can see Tony preparing to install an exterior door in the rough opening.
- The housewrap product (Weather Resistant Barrier or WRB) is stapled over the building sides from the bottom run up, so that upper runs of wrap lap over the lower sections.
- Install the sill pan or RO bottom flashing: Best practice is to use a pre-fabricated sill pan under windows or doors; the sill plate is set into the RO as directed by the window or door manufacturer.
Install the sill pan or fabricated sill pan flashing using flashing tape around and under the window or door R.O. bottom. Add a second course of flashing tape on the sill surface as shown in the example at above/left, adapted from Pella® Window installation instructions cited later in this article.
In all cases, the RO Bottom flashing pan or tape are installed before the window is set into the opening.
- Above the RO the housewrap is cut and lifted over the window or door opening so that flashing tape installed in this location will be under the housewrap. You can use snippets of flashing tape or masking tape to hold the housewrap 'up' out of the way while setting the window and while applying head flashing tape over the window.
- The window or door is set into the rough opening, squared, shimmed, and nailed in place through the flanges.
- Then set the window. See our notes below about window shims & interior & exterior WINDOW SEALANTS.
- Second flashing tape course: along the window left and right sides, with the bottom of the flashing tape lapping over the top of the horizontal tape that runs below the window. Our photo at below left just above shows these two flashing tapes have been installed. Details are shown below.
- Finally third flashing tape course across the window top: the horizontal top of the window is sealed with peel and stick flashing tape, with its ends lapping over the top of the flashing tape that ran along the window sides. The top flashing tape should extend at least 1' past the vertical side flashing tape. Our page top photo shows a common peel-and stick-on flashing product installed around a window during new construction. There the flashing tape was installed on top of the housewrap - not the best practice.
This flashing tape is very sticky on one side (peel off the waxed paper as we show). The other side of this product is covered with aluminum foil to improve its performance. This sticky flashing membrane tape will also seal nails that may penetrate its surface after installation.
But Pella® is smart for recommending this under-the WRB detail. As we found in the field, even very sticky flashing tape does not always bond well to some housewrap products. Eric Galow recommends additional staples through the flashing tape to be sure it remains in place during initial curing of the bonding adhesive. The window and flashing tape manufacturers recommend using plastic coated / capped nails or staples. Try and find them!
Also see FLASHING WALL DETAILS and FLASHING ROOF WALL DETAILS.
If you are building a deck see DECK FLASHING at BUILDING.
Peel-and-stick eaves membranes have been used for nearly20 years to prevent roof leaks from ice dams and otherroofing trouble spots.
These are typically available in 36-inch widths and are used to protect eaves, shallow-pitch roofs, and other problem roof areas. Over the past few years, a new family of related products has been introduced to help seal walls against water intrusion.
Question: which is the right way to install peel and stick flashing below a window
2016/09/13 Pat said:
Can someone please clarify this issue? Most everywhere I've read about window flashing tape, it states to never apply it to the bottom of the window on the outside so water can exit to the house wrap instead of under the house wrap.
My siding crew taped the bottom of the window like shown in this article but I'm less worried about it because there's an open flap of house wrap below the window where water can eventually exit. Also, I insisted on a rain screen and the house wrap should let water escape so it should get stuck inside. Either way, I don't think taping the bottom is hardly ever recommended.
This question was posted originally at FLASHING MEMBRANES PEEL & STICK
[Click to enlarge any image] This photo of flashing tape installed below a window and over the window's bottom flange or fin does not show the very best installation practice. Photos by D Friedman & Eric Galow, Galow Homes.
Reply:
Pat:
You're quite correct. The first example in the WR Grace Vycor Plus window flashing details, shown for a flanged window in new work, includes the use of a sill pan fabricated from flashing tape.
That's a good installation procedure if a pre-fabricated sill pan has not been provided. Other manufacturers simply run a full width of flashing tape just below the R.O. for the window before the window is set.
Watch out: Pella warns: DO NOT tape or seal the bottom nailing fin of the window itself - as was done here. Presumably we leave this window or door bottom fin open so that should water from above leak into the window or door R.O. it might find its way out onto the outer surface of the building's WRB (weather resistant barrier or 'housewrap').
Flashing tape below the window at the sill should be installed over the housewrap or weather-resistant barrier (WRB) and before the window has been set into the R.O. A better detail from Fortifiber and still better details using a sill pan or fabricating one are both shown in more detail below.
[Click to enlarge this WR Grace Vycor Plus illustration sent along by Pat - Ed.]
How To Install Window And Door Flashing Tape
Above: Flashing tape installed as sill flashing below the window R.O. before the window is set. This detail is from Fortifiber's® Window Flashing Installation Guide cited in this article. Other manufacturers recommend installing a sill pan or fabricating one from flashing tape before the window is set.
As for our photo of Typar® flashing tape used under new work windows shown above in this article, you will see that same detail in the Typar® flashing tape manual found at FLASHING TAPE INSTALLATION MANUALS. As my much-admired building instructor Bernie Campbalik said, 'follow the water, boys, follow the water!' Typar says also that installation methods are approved by the American Architectural Manufacturers Association (AAMA) are also acceptable for TYPAR products and system warrantee.
Be afraid, be very afraid, of 'experts' who insist, willy-nilly, that you should never ever use flashing tape below a window or door at all - that's not correct. But be just as afraid too (as you are) lest you install the flashing tape incorrectly in that location. In sum, flashing tape used as a window or door pan or installed below a window or door goes on before the window is set.
While there may be some window designs and some siding installation guides that recommend omitting window bottom flashing tape to permit window draining, virtually all of the FLASHING TAPE INSTALLATION MANUALS cited below describe some sort of window bottom stick-on flashing installation.
When a window pan or door pan is not used, many guides recommend fabricating one out of flashing tape. Some of the guides show two passes with flashing tape, one as a window or door pan and a second later in the window or door installation.
For example, the Flashing Tape Manual, Berry Plastics & Polyken Nashua Tape Products clearly shows the use of flashing tape under the window sill in different details depending on the type of window and sill and depending on whether or not a sill pan was used.
Similar advice is in the the Zip Wall Installation Manual and in the Dupont Flashing Systems Guide. There you'll also see flashing tape used across the bottom side of the window. Dupont® also suggests carrying the tape up over the RO sill before the window is set.
Here is an excerpt from Typar's® instructions for window sealing and flashing. I've made minor corrections to spelling, grammar and clarity.
- Install the window sill pan according to the manufacturer's instructions. Alternatively, you can create a sill pan using Typar Flashing Flex. Cut a piece that is 12' longer than the length of the rough opening window sill.
Carefully pull off the release liner. Center the Flashing in the center of the rough opening and work your way toward the corners and then up the sides. Note: the flex flashing should overlap the outside of the wall by 2-3'. Only stretch the flashing in the corners.
Alternatively to above you, you can create a sill pan by installing TYPAR Straight Flashing along the bottom sill and installing Typar Flex on the corners only.
If needed, secure the fanned edges of the TYPAR Flashing Flex with a plastic capped nail/plastic capped staple. [We always do this]. - Apply a continuous bead of sealant to the back of the window or on the wall. Do not apply the sealant across the bottom of the sill or on the bottom of the window. [THIS is where more confusion probably arises about the use of flashing tape as we want any water that is on the window sill or on the sill RO to be able to drain out.- Ed.]
Install the window according to the manufacturer's installation instructions. - Cut two pieces of Typar Flashing long enough to extend 1' above the window head flange and 1' below the window sill flange. Carefully peel off the release liner and apply the flashing on both sides of the window. Make sure to cover the entire window flange; press firmly by hand or using a J-roller. Ensure that there are no wrinkles or bubbles.
Cut a piece of Typar Flashing for the head flashing. Ensure that the piece is long enough to extend 1' on both sides of the jamb flashing. Remove the release liner and carefully install the flashing. Cover the window flange and press firmly by hand or using a J-roller. - Release the upper flap of the WRB [Weather Resistant Barrier, aka 'housewrap'] that you cut earlier. Tape the 45 degree cuts using Typar construction Tape or Typar Flashing. DO NOT tape the WRB along the top of the window flange.
Window Shims & Sealants
Watch out: don't forget to use your window shims and spacers at this step to be certain that the window is plumb and level, and to prevent movement of the window within the R.O. Don't over-jam shims or spacers as you don't want to bow the window frame. Pella's window installation instructions for inserting the window into the rough opening do not specify any use of sealant under the window fins nor around the interior of its jamb.
Sealant is used at the exterior of the window such that ' .. the exterior sealant line will cover the exterior edge of the [flashing] tape. Later, from the building interior, insulating foam sealant is later applied in the space between the window frame and the rough-opening sides. Pella warns DO NOT completely fill the space from the back of the fin to the interior face of the opening.
Check the window operation when the foam sealant has cured. If the window does not operate correctly, check that it has remained plumb, level, and that its sides are not bowed. If necessary, but away foam sealant with a serrated knife and adjust the shims. We use a bread knife or a Japanese carpenter's saw for this purpose.
Typically a backer rod and sealant are used between siding J-channel or wood trim and the window head. Because I don't want water to run behind horizontal wood trim where it will then get trapped by the sealant used at the trim underside, I also use sealant along the back side of my horizontal wood trim at the trim top edge, and I add sealant at the juncture of wood siding and horizontal wood trim as well.
Installation Manuals for Flashing Tapes and Membranes
- Berry Plastics Flashing Tape Manual, [PDF] Berry Plastics & Polyken Nashua Tape Products, distributed by various sources including Best Materials, retrieved 2016/09/13, original source:
www.bestmaterials.com/PDF_Files/flashing-tapes-manual.pdf - Dupont Flashing Systems Manual, prior, [PDF] retrieved 2016/09/13, original source:
www.dupont.com/content/dam/assets/products-and-services/construction-materials/assets/K17933-FlashingGuidelinesBEFORE-10-30-11.pdf - Dupont Flashing Systems Manual - current, PDF] retrieved 2016/09/13, original source:
- Fortifiber flashing tape manual, [PDF] retrieved 2016/09/13, original source: http://www.fortifiber.com/pdf/install_guides/IG_window_flashing_method_a1.pdf
- Pella Window Flashing Details, [PDF], retrieved 2016/09/13, original source:
- Typar Flashing Tape Manual, [PDF] retrieved 2016/09/13, original source: www.typar.com/assets/downloads/pdf/TYPAR_WPS_Install_Instructions_5-19-15.pdf
- Zip Wall Installation Manual, [PDF] retrieved 2016/09/13, original source: sweets.construction.com/swts_content_files/102935/821515.pdf
- See FLASHING TAPE BRANDS, SOURCES, MANUALS for a list of sources & producers of peel and stick tapes and flashing products
..
Continue reading at FLASHING MEMBRANES PEEL & STICK - topic home, or select a topic from the closely-related articles below, or see the complete ARTICLE INDEX.
Or see these Why is fortnite so laggy on mac.
Recommended Articles
- PEEL & STICK FLASHING MEMBRANES
- WINDOW & DOOR FLASHING TAPE DETAILS - separate article
Suggested citation for this web page
WINDOW & DOOR FLASHING TAPE DETAILS at InspectApedia.com - online encyclopedia of building & environmental inspection, testing, diagnosis, repair, & problem prevention advice.
Or see this
INDEX to RELATED ARTICLES: ARTICLE INDEX to BUILDING FLASHING
Or use the SEARCH BOX found below to Ask a Question or Search InspectApedia
.. How to download minecraft pc on mac.
Ask a Question or Search InspectApedia
Try the search box just below, or if you prefer, post a question or comment in the Comments box below and we will respond promptly.
Search the InspectApedia website
Note: appearance of your Comment below may be delayed:if your comment contains an image, web link, or text that looks to the software as if it might be a web link, your posting will appear after it has been approved by a moderator. Apologies for the delay.
Technical Reviewers & References
- Best Practices Guide to Residential Construction, by Steven Bliss. John Wiley & Sons, 2006. ISBN-10: 0471648361, ISBN-13: 978-0471648369, Hardcover: 320 pages, available from Amazon.com and also Wiley.com. See our book review of this publication.
- Eric Galow, Galow Homes, Lagrangeville, NY. Mr. Galow can be reached by email: ericgalow@gmail.com or by telephone: 914-474-6613. Mr. Galow specializes in residential construction including both new homes and repairs, renovations, and additions.
- Paul Galow [Website galowconsulting.com ] - technical consultant on networking, LAN design, applications support. Galow Consulting Services [Website galowconsulting.com ] , 914-204-1749, email: paulgalow@galowconsulting.com
- John Rudy, Advantage Home Inspections, Flemington N.J. 08822 home inspector, 908-806- 6364, Home, Radon & Termite Inspections, Central & Parts of North New Jersey, email: jonadvantage1@yahoo.com
Books & Articles on Building & Environmental Inspection, Testing, Diagnosis, & Repair
- Our recommended books about building & mechanical systems design, inspection, problem diagnosis, and repair, and about indoor environment and IAQ testing, diagnosis, and cleanup are at the InspectAPedia Bookstore. Also see our Book Reviews - InspectAPedia.
- Decks and Porches, the JLC Guide to, Best Practices for Outdoor Spaces, Steve Bliss (Editor), The Journal of Light Construction, Williston VT, 2010 ISBN 10: 1-928580-42-4, ISBN 13: 978-1-928580-42-3, available from Amazon.com
- The Journal of Light Construction has generously given reprint permission to InspectAPedia.com for this article. All rights and contents are ©Journal of Light Construction and may not be reproduced in any form.
- ..
- Carson, Dunlop & Associates Ltd., 120 Carlton Street Suite 407, Toronto ON M5A 4K2. Tel: (416) 964-9415 1-800-268-7070 Email: info@carsondunlop.com. The firm provides professional HOME INSPECTION SERVICES and also extensive HOME INSPECTION EDUCATION and home inspection-related PUBLICATIONS. Alan Carson is a past president of ASHI, the American Society of Home Inspectors.
Thanks to Alan Carson and Bob Dunlop, for permission for InspectAPedia to use text excerpts from The Home Reference Book & illustrations from The Illustrated Home. Carson Dunlop Associates' provides extensive home inspection education and report writing material.
The ILLUSTRATED HOME illustrates construction details and building components, a reference for owners & inspectors.
Special Offer: For a 5% discount on any number of copies of the Illustrated Home purchased as a single order Enter INSPECTAILL in the order payment page 'Promo/Redemption' space.
TECHNICAL REFERENCE GUIDE to manufacturer's model and serial number information for heating and cooling equipment, useful for determining the age of heating boilers, furnaces, water heaters is provided by Carson Dunlop Weldon & Associates
Special Offer: Carson Dunlop Associates offers InspectAPedia readers in the U.S.A. a 5% discount on any number of copies of the Technical Reference Guide purchased as a single order. Just enter INSPECTATRG in the order payment page 'Promo/Redemption' space. - The HOME REFERENCE BOOK - the Encyclopedia of Homes, Carson Dunlop & Associates, Toronto, Ontario, 25th Ed., 2012, is a bound volume of more than 450 illustrated pages that assist home inspectors and home owners in the inspection and detection of problems on buildings. The text is intended as a reference guide to help building owners operate and maintain their home effectively. Field inspection worksheets are included at the back of the volume.
Special Offer: For a 10% discount on any number of copies of the Home Reference Book purchased as a single order. Enter INSPECTAHRB in the order payment page 'Promo/Redemption' space. InspectAPedia.com editor Daniel Friedman is a contributing author.
Or choose the The HOME REFERENCE eBook for PCs, Macs, Kindle, iPad, iPhone, or Android Smart Phones.
Special Offer: For a 5% discount on any number of copies of the Home Reference eBook purchased as a single order. Enter INSPECTAEHRB in the order payment page 'Promo/Redemption' space. - Building inspection education & report writing systems from Carson, Dunlop & Associates Ltd
COMMERCIAL BUILDING INSPECTION COURSES - protocol ASTM Standard E 2018-08 for Property Condition Assessments
HOME INSPECTION EDUCATION COURESES (Canada)
HOME INSPECTION EDUCATION COURSES (USA) including home study & live classes at eleven colleges & universities.
HOME INSPECTION EDUCATION: HOME STUDY COURSES - ASHI@Home Training 10-course program.
Special Offer: Carson Dunlop Associates offers InspectAPedia readers in the U.S.A. a 5% discount on these courses: Enter INSPECTAHITP in the order payment page 'Promo/Redemption' space. InspectAPedia.com editor Daniel Friedman is a contributing author. - The Horizon Software System manages business operations,scheduling, & inspection report writing using Carson Dunlop's knowledge base & color images. The Horizon system runs on always-available cloud-based software for office computers, laptops, tablets, iPad, Android, & other smartphones
